Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - turftracracer19

Pages: [1] 2
1
Driveline / Re: 700 extention/ jackshaft
« on: January 30, 2014, 12:06:20 am »
I just built an extension with no machining involved using parts of an old 700. Here's a link to my build. Youll find the pics as to how I built it in my thread.

http://woochat.freeforums.net/thread/89/mod-mtd-build

2
Other Interesting Builds / Re: V Twin MINI Midget
« on: January 28, 2014, 05:54:41 pm »
Where are you located in Ontario? I'm southwestern, approximately 2 hours east of toronto

3
Briggs OHV & Vanguard / Re: 14.5hp ohv torque specs
« on: February 20, 2012, 01:42:29 am »
thanks i have the info that i need now

4
Briggs OHV & Vanguard / 14.5hp ohv torque specs
« on: February 19, 2012, 06:37:28 pm »
after a good clean/inspection iv decided to put my 14.5 ohv briggs back together. does anybody know the torque specs for everything that should be torqued? i have looked everywhere with no luck  :(

5
Coffee Shop / Re: New Ford Build
« on: October 21, 2011, 08:42:16 pm »
hey im in straffordville ontario. im like 15 minutes from tillsonburg. i was going to start racing in WOO but my time became too occupied between work and me and my dads project car. maybe i could show you some of the basics when it comes to building a racer.

6
Post your Pics! / Re: trbinrat's parts and tractor pics
« on: May 26, 2011, 12:05:48 am »
looks like you need a front end alignment :P

7
Chassis / Re: Easy Radius Rods!
« on: January 04, 2011, 11:25:53 pm »
to prevent aluminum from sticking to my cut off wheel i take a stick of candle wax to the cut off wheel, works really good

8
Garden Tractor Pulling / Re: Thinking of getting into it...
« on: January 03, 2011, 08:22:54 pm »
never dull works very well, it'll take off surface rust no problem just takes time

9
Post your Pics! / Re: What Wheel Horse?
« on: July 15, 2010, 09:10:21 pm »
are your spindles 5/8" diameter? if they aren't, then they wont work for standard kart hubs.

10
Post your Pics! / Re: My first build...
« on: July 15, 2010, 12:14:49 am »
i might be wrong but those spindle angles dont look quite right lol

11
Post your Pics! / Re: What Wheel Horse?
« on: July 14, 2010, 07:26:10 pm »
im pretty sure wheelhorseracer built one of these, ask him, he should know ;)

12
Driveline / Re: Will Husky fit my MTD????
« on: July 14, 2010, 05:41:15 pm »
my friends 12.5hp husky has a 3 speed trans axle in it

13
Post your Pics! / Re: My first build...
« on: July 11, 2010, 11:43:10 pm »
iv been thinking about building one of these mowers, cant wait to see what it looks like finished  :P

14
Driveline / Re: good quality chain that might stretch less?
« on: June 17, 2010, 10:47:13 pm »
D.I.D o-ring chain is the way to go, iv had one on my dirtbike for 2 seasons of racing and it hasnt stretched at all.

15
Chassis / Re: Bumper mounting
« on: April 24, 2010, 06:02:27 pm »
what size tubing is that? :confused:, looks like it could get bent into the back of your tire if hit hard enough

Pages: [1] 2