Author Topic: FC420v-ds10 kawa  (Read 8759 times)

0 Members and 1 Guest are viewing this topic.

Offline bigdawg

  • Newbie
  • *
  • Posts: 27
  • Karma: 0
  • Gender: Male
    • View Profile
Re: FC420v-ds10 kawa
« Reply #15 on: January 16, 2008, 07:03:04 PM »
George i found a carb that will fit. It has everything the same except the main jet. The old 1 had the jet on the side of the broken piece. the new 1 has it leading to the inside of the carb. how could i jet this type of carb for more fuel. it probaly needs more air/fuel ratio too. can u help me out. thanx

Offline George Herrin

  • aka SUPERMAN
  • Superman
  • Highly Mowtivated
  • *
  • Posts: 17792
  • Karma: 102
  • Gender: Male
  • I am going to Race Every Race like its my last one
    • View Profile
    • BTMRA Home/Forum An Independant Club.
Re: FC420v-ds10 kawa
« Reply #16 on: January 16, 2008, 07:49:58 PM »
if it needs mopre fuel drill the main jet size out. Small changes very small changes at a time
George Herrin #6
Indian Power.. You gotta Go big to beat em or Go HOME
8 time ARMA National Champion
4 time USLMRA National Champion
Retired from BP
www.herrinmowersports.yolasite.com
www.allamericanmowerchampionships.yolasite.com
My other racer is a 1/5th scale Dirt Late Model!!!!

Offline bigdawg

  • Newbie
  • *
  • Posts: 27
  • Karma: 0
  • Gender: Male
    • View Profile
Re: FC420v-ds10 kawa
« Reply #17 on: January 17, 2008, 10:34:48 PM »
on a kawi. how much could i shave the heads without running into problems. i didnt see any post about porting and polishing a kawasaki. how could i port the exhaust and polish up the intake


Offline George Herrin

  • aka SUPERMAN
  • Superman
  • Highly Mowtivated
  • *
  • Posts: 17792
  • Karma: 102
  • Gender: Male
  • I am going to Race Every Race like its my last one
    • View Profile
    • BTMRA Home/Forum An Independant Club.
Re: FC420v-ds10 kawa
« Reply #18 on: January 18, 2008, 12:36:11 AM »
on a kawi. how much could i shave the heads without running into problems. i didnt see any post about porting and polishing a kawasaki. how could i port the exhaust and polish up the intake

You can shave any head .030 safely. Course if ya running a really huge lift cam that could come into play. As for porting and polishing. Its all the same principle. Regardless of engine brand. Port shape plays a big roll in OHV's and I am not getting into a deep discussion on this.
George Herrin #6
Indian Power.. You gotta Go big to beat em or Go HOME
8 time ARMA National Champion
4 time USLMRA National Champion
Retired from BP
www.herrinmowersports.yolasite.com
www.allamericanmowerchampionships.yolasite.com
My other racer is a 1/5th scale Dirt Late Model!!!!

Offline bigdawg

  • Newbie
  • *
  • Posts: 27
  • Karma: 0
  • Gender: Male
    • View Profile
Re: FC420v-ds10 kawa
« Reply #19 on: January 18, 2008, 10:03:18 PM »
thanx george for ur help.

Offline jaysonmikula

  • Newbie
  • *
  • Posts: 99
  • Karma: 1
  • Gender: Male
    • View Profile
Re: FC420v-ds10 kawa
« Reply #20 on: February 12, 2008, 11:12:33 PM »
there is three wires running to flywheel cover.. There is two black ones and a white one. someone told to take the two black ones off. they runn to the flywheel. then the white one runs to magneto
The other thing that may be working against you is the fact that most of these Kawi's require a seperate igniter chip (control module in the attachted diagram) to make the magneto work.

Offline johnboy

  • Turf Warrior
  • **
  • Posts: 235
  • Karma: 2
  • Gender: Male
    • View Profile
Re: FC420v-ds10 kawa
« Reply #21 on: February 13, 2008, 06:55:39 AM »
I found this and its all I have ever found on Kaw. parts.    http://kawpower.com     hope ithelps you some
Sometimes imagination can be even more powerful than knowledge !


Offline bigdawg

  • Newbie
  • *
  • Posts: 27
  • Karma: 0
  • Gender: Male
    • View Profile
Re: FC420v-ds10 kawa
« Reply #22 on: February 14, 2008, 08:13:08 PM »
thanx johnboy got it running couple weeks ago

 

anything