Author Topic: Building a 23hp vanguard  (Read 4151 times)

0 Members and 1 Guest are viewing this topic.

Offline Cnrenner

  • Newbie
  • *
  • Posts: 3
  • Karma: 0
    • View Profile
Building a 23hp vanguard
« on: August 15, 2018, 01:52:14 pm »
I am new to this site and asking for some advice. I have a 23hp vanguard on a mud motor i would like to up the hp to between 30 and 35 hp and maybe turn a few more rpms too. But what do i need to do to this stock motor to see them results would like to keep it cheap n fast. If you guys can give me some pointers n maybe some sites to get parts from that would be great. Thank you in advance.

Offline Mower Maniac

  • Turf Warrior
  • **
  • Posts: 116
  • Karma: 1
  • Gender: Male
    • View Profile
Re: Building a 23hp vanguard
« Reply #1 on: August 15, 2018, 06:18:57 pm »
Carrier performance
AZLMRA
2016-GPK 3rd place
2017-GPK 2nd place

Offline cycloneracer

  • Easy Parcheesy!!!!!!!
  • Global Moderator
  • Highly Mowtivated
  • *****
  • Posts: 4117
  • Karma: 37
  • Gender: Male
  • Easy Parcheesy!!!!!!!
    • View Profile
Re: Building a 23hp vanguard
« Reply #2 on: August 15, 2018, 11:00:29 pm »
Billet flywheel.
upgrade valve train
cam

And FYI    Fast isn't cheap.

Paul Krueger

****2017 USLMRA FXT points Champion****

#150 Worlds First "sidewinder" FX (now dismantled)

#150 FXT  Sponsored by Zach Kerber Machine. http://zkbrmachine.com/

Easy Parcheesy Racing

Offline Cnrenner

  • Newbie
  • *
  • Posts: 3
  • Karma: 0
    • View Profile
Re: Building a 23hp vanguard
« Reply #3 on: August 16, 2018, 09:48:28 am »
I understand fast isnt cheap but what i was meaning is bilt on stuff i dont really want to have to tear down n put new crank, rods n pistons in to make fast if all possible i would just assume to keep bottom end stock

Offline Cnrenner

  • Newbie
  • *
  • Posts: 3
  • Karma: 0
    • View Profile
Re: Building a 23hp vanguard
« Reply #4 on: August 18, 2018, 09:16:37 am »
So by upgrading valve terrain i need valves springs rockers correct n what cam would u reccomend. Also do i need to deck the heads to raise the compression a lil

Offline rotten ron

  • Turf Warrior
  • **
  • Posts: 610
  • Karma: 10
  • Gender: Male
    • View Profile
Re: Building a 23hp vanguard
« Reply #5 on: August 19, 2018, 12:21:45 am »
If you don't put better rods in it you won't be able to rev it to where it can make some power,The stock rod are probably good  for about 4500 RPM and you will need to run it almost twice that high to get some power out of it,more compression makes more power too so you should mill the heads,then you will need a better camshaft too.The 23 HP heads are some of the best flowing but they need porting  and better valves springs and retainers.The stock rocker arms are not much good for racing either

Offline thompsoncustom

  • Newbie
  • *
  • Posts: 18
  • Karma: 0
  • Gender: Male
    • View Profile
Re: Building a 23hp vanguard
« Reply #6 on: August 20, 2018, 09:14:38 pm »
The most important question here is longtail or surface drive which is your setup?
Daniel Thompson

 

anything