Author Topic: Digatron dt-32k1  (Read 1757 times)

0 Members and 1 Guest are viewing this topic.

Offline Racer57

  • Newbie
  • *
  • Posts: 85
  • Karma: 0
  • Gender: Male
    • View Profile
Digatron dt-32k1
« on: April 15, 2014, 07:04:11 AM »
Does anybody run one of these, i bought a use done and oneofthe sensors were damaged, I assume the bronze colored sensor goes under the spark plug, what's the other sensor, where does it hook to?


2013 NNYLMR Mod xr points champion

Offline Jeff McKelroy

  • Professor Ducky
  • Turf Warrior
  • **
  • Posts: 890
  • Karma: 10
  • Gender: Male
    • View Profile
Re: Digatron dt-32k1
« Reply #1 on: April 15, 2014, 07:22:37 AM »
Is it threaded on the end/has a threaded nut?  That's the thermocouple for the exhaust.

Is it a wire with a blunted end?  That's your tach.

The temp sensor you might be referring to for the spark plug will look like a brass washer.

Offline Racer57

  • Newbie
  • *
  • Posts: 85
  • Karma: 0
  • Gender: Male
    • View Profile
Re: Digatron dt-32k1
« Reply #2 on: April 15, 2014, 07:27:28 AM »
There is no end on the other wire, and yes it looks like a brass washer
2013 NNYLMR Mod xr points champion


Offline SCF

  • Newbie
  • *
  • Posts: 26
  • Karma: 0
  • Gender: Male
    • View Profile
Re: Digatron dt-32k1
« Reply #3 on: April 15, 2014, 08:51:35 AM »
CHT Sensor- the one that looks like a brass washer on the end
Remove the spark plug from the cylinder you wish to monitor
and discard the plug washer.
Check the surface of the head around the spark plug hole for a
smooth, flat finish to assure a good seal when the sensor is
installed.
Position the sensor over the spark plug hole and check to be
sure you have sufficient clearance around the outside of the
sensor body to avoid damage when the plug is installed and
tightened.
Install the spark plug finger tight to hold the sensor in position.
Finish tightening with a plug wrench to the same torque as
normally recommended. Do not allow the sensor to turn as you
tighten the plug
. The sensor is easily damaged if forced into a
cooling fin.
Route the sensor cable from the motor to the instrument.
Secure the cable to the frame with cable ties.
Connect to the RF style pigtail on the instrument and turn the
connector until tight.

TACH Sensor the blunt end one
To install them, clamp or tie-rap the blunt end of the tach sensor to a
plug wire, 1 " from the spark plug end. Try to keep the end of the
sensor parallel to the plug wire and route the cable as far away
from the ignition coil as far possible.
SCF Racing
CP/Mod-X
Frank Knapp

Offline Racer57

  • Newbie
  • *
  • Posts: 85
  • Karma: 0
  • Gender: Male
    • View Profile
Re: Digatron dt-32k1
« Reply #4 on: April 15, 2014, 02:01:27 PM »
Could u post a picture of your set up please
2013 NNYLMR Mod xr points champion

Offline SCF

  • Newbie
  • *
  • Posts: 26
  • Karma: 0
  • Gender: Male
    • View Profile
Re: Digatron dt-32k1
« Reply #5 on: April 17, 2014, 09:22:01 AM »
I sent you an email with info..good luck
SCF Racing
CP/Mod-X
Frank Knapp

Offline Racemower16

  • Newbie
  • *
  • Posts: 2
  • Karma: 0
  • Gender: Male
    • View Profile
Re: Digatron dt-32k1
« Reply #6 on: September 12, 2019, 09:00:55 AM »
I know this is an old thread but what setting in did you use to have the tach read accurate with a single cyl coil


 

anything