Author Topic: clutches  (Read 2990 times)

0 Members and 1 Guest are viewing this topic.

Offline finn1

  • Turf Warrior
  • **
  • Posts: 153
  • Karma: 1
  • Gender: Male
    • View Profile
clutches
« on: January 14, 2014, 09:41:25 am »
supermod guys just wondering if I can get your 2 cents on what clutches you use. this is mainly for belt clutches not chain thanks bob
bob finnerty
2010-one time Lightning Larry Lanning beater
2010 creekside raceway mx champ

Offline Tim Toleson

  • I been wrist slapped!!
  • Turf Warrior
  • **
  • Posts: 638
  • Karma: 2
  • Gender: Male
    • View Profile
Re: clutches
« Reply #1 on: January 14, 2014, 10:49:24 am »
I use a 2x4 and a pair of skateboard wheel. SECRETS OUT!
 :woo:
Thank you to Whitney\'s Garage (315) 675-8592, and Mountain Man\'s Famous Fudge  (315) 623-9598 for your support in the 2012 ARMA racing season!

2012 ARMA 3rd place North East Region - Mod-X
2012 ARMA 5th place Overall - Mod-X

Offline finn1

  • Turf Warrior
  • **
  • Posts: 153
  • Karma: 1
  • Gender: Male
    • View Profile
Re: clutches
« Reply #2 on: January 14, 2014, 12:03:48 pm »
hmmm that explains a lot.  :P
bob finnerty
2010-one time Lightning Larry Lanning beater
2010 creekside raceway mx champ

Offline Old Goat

  • Mow-Forum Junkie
  • ***
  • Posts: 1266
  • Karma: 10
  • Gender: Male
    • View Profile
    • Juniata County Outlaws Mower Racing Club
Re: clutches
« Reply #3 on: January 14, 2014, 08:22:02 pm »
Are you using a vertical or horizontal shaft motor?
Jim Klauss
Boogity Boogity boys, let's go racin'
http://jcomrc.com/

Offline finn1

  • Turf Warrior
  • **
  • Posts: 153
  • Karma: 1
  • Gender: Male
    • View Profile
Re: clutches
« Reply #4 on: January 14, 2014, 08:57:33 pm »
horizontal 1 inch on the crank. good to see you on here again old goat
bob finnerty
2010-one time Lightning Larry Lanning beater
2010 creekside raceway mx champ

Offline finn1

  • Turf Warrior
  • **
  • Posts: 153
  • Karma: 1
  • Gender: Male
    • View Profile
Re: clutches
« Reply #5 on: February 06, 2014, 12:25:17 pm »
I need a clutch 1" bore belt pulley for a vertical engine any suggestions? thanks bob
bob finnerty
2010-one time Lightning Larry Lanning beater
2010 creekside raceway mx champ

Offline George Herrin

  • aka SUPERMAN
  • Superman
  • Highly Mowtivated
  • *
  • Posts: 17732
  • Karma: 102
  • Gender: Male
  • I am going to Race Every Race like its my last one
    • View Profile
    • BTMRA Home/Forum An Independant Club.
Re: clutches
« Reply #6 on: February 06, 2014, 12:46:31 pm »
18 tooth stAr clutch get a blank Pulley it will slide right on an weld. But why belt chai don't slip an works well
George Herrin #6
Indian Power.. You gotta Go big to beat em or Go HOME
8 time ARMA National Champion
4 time USLMRA National Champion
Retired from BP
www.herrinmowersports.yolasite.com
www.allamericanmowerchampionships.yolasite.com
My other racer is a 1/5th scale Dirt Late Model!!!!

Offline Old Goat

  • Mow-Forum Junkie
  • ***
  • Posts: 1266
  • Karma: 10
  • Gender: Male
    • View Profile
    • Juniata County Outlaws Mower Racing Club
Re: clutches
« Reply #7 on: February 06, 2014, 08:51:31 pm »
I need a clutch 1" bore belt pulley for a vertical engine any suggestions? thanks bob

This is what I use.  http://maskapulleys.com/accueil.htm#   I find the part number I need and get the local tractor dealership to order it.
Jim Klauss
Boogity Boogity boys, let's go racin'
http://jcomrc.com/