Author Topic: Vanny vtwin 14hp stock cam spacer  (Read 869 times)

0 Members and 1 Guest are viewing this topic.

Offline GTX21

  • Turf Warrior
  • **
  • Posts: 696
  • Karma: 1
  • PA Posse Rulez!!!
    • View Profile
Vanny vtwin 14hp stock cam spacer
« on: February 17, 2013, 10:40:23 AM »
I've searched on hear and read about a spacer that needs to be made in order to maintain oil pressure on a bare no governor stock vanguard twin cam. I've removed everything on the cam, it's now hollow. I just don't understand what the spacer is suppose to look like and the best way to do it. A picture of this spacer would help a bunch!


Nathan Mansberger
                   
If your NOT 1st your LAST!


Offline George Herrin

  • aka SUPERMAN
  • Superman
  • Highly Mowtivated
  • *
  • Posts: 17732
  • Karma: 102
  • Gender: Male
  • I am going to Race Every Race like its my last one
    • View Profile
    • BTMRA Home/Forum An Independant Club.
Re: Vanny vtwin 14hp stock cam spacer
« Reply #1 on: February 17, 2013, 11:06:50 AM »
A small tube that goes inside of the cam core you will need to stick a long skinny rod into the cam from opposite end of ball. Popping ball out be sure you have a rag around it or you will loose parts. There will be a ball a cup a spring and a washer. Using calipers measure from the shoulder the washer sits on down to the shoulder inside cam that will be how long the spacer slah tube is. Been along time since I have done one so do not remember how long it is. Hope this helps cause I got no pictures.
George Herrin #6
Indian Power.. You gotta Go big to beat em or Go HOME
8 time ARMA National Champion
4 time USLMRA National Champion
Retired from BP
www.herrinmowersports.yolasite.com
www.allamericanmowerchampionships.yolasite.com
My other racer is a 1/5th scale Dirt Late Model!!!!


Offline GTX21

  • Turf Warrior
  • **
  • Posts: 696
  • Karma: 1
  • PA Posse Rulez!!!
    • View Profile
Re: Vanny vtwin 14hp stock cam spacer
« Reply #2 on: February 17, 2013, 11:24:03 AM »
When you say measure is it from where the washer sat to the top of cam?(lobe side) or the side the ball and spring came out of?
Nathan Mansberger
                   
If your NOT 1st your LAST!

Offline George Herrin

  • aka SUPERMAN
  • Superman
  • Highly Mowtivated
  • *
  • Posts: 17732
  • Karma: 102
  • Gender: Male
  • I am going to Race Every Race like its my last one
    • View Profile
    • BTMRA Home/Forum An Independant Club.
Re: Vanny vtwin 14hp stock cam spacer
« Reply #3 on: February 17, 2013, 12:20:21 PM »
from where the washer sat/sits down into the cam. When done it will go in as a easy droping kinda snug fit (not a drive in fit) then washer goes in and sits on original shoulder then sroing and ball with retaining cup.
George Herrin #6
Indian Power.. You gotta Go big to beat em or Go HOME
8 time ARMA National Champion
4 time USLMRA National Champion
Retired from BP
www.herrinmowersports.yolasite.com
www.allamericanmowerchampionships.yolasite.com
My other racer is a 1/5th scale Dirt Late Model!!!!

 

anything