« previous next »
Pages: [1]   Go Down

Author Topic: mikuni carbs  (Read 3110 times)

0 Members and 1 Guest are viewing this topic.

Offline ajm57

  • Newbie
  • *
  • Posts: 27
  • Karma: 0
  • Gender: Male
    • View Profile
mikuni carbs
« on: March 10, 2012, 12:27:25 am »
Does anyone know where to find a chart for what cfms the various models of mikuni carbs flow?
thanks
Logged
Arthur

Offline Ron Atchison/A.C.E. Race Engines

  • Turf Warrior
  • **
  • Posts: 327
  • Karma: 4
  • Gender: Male
  • A.C.E. race engines
    • View Profile
Re: mikuni carbs
« Reply #1 on: March 11, 2012, 10:49:54 pm »
Quote from: ajm57 on March 10, 2012, 12:27:25 am
Does anyone know where to find a chart for what cfms the various models of mikuni carbs flow?
thanks

what sizes specifically/what engine combo?
Logged
home of A.C.E. the race engines
\"building winning race engines..one at a time\"
ronatchison@live.com  FB>Ace Racing and Performance.

Offline ajm57

  • Newbie
  • *
  • Posts: 27
  • Karma: 0
  • Gender: Male
    • View Profile
Re: mikuni carbs
« Reply #2 on: March 12, 2012, 08:00:24 am »
38 cube long rods .02 over cam and flywheel. 35 cube heads
I will mill the heads ~.035- .04 if I go single carb.  or more with dual carb.
I'm just trying to figure which way to go and what to use. I want to make sure I have enough, but I don't want to go to far either. Any suggestions are apprieciated.
Logged
Arthur

Offline Ron Atchison/A.C.E. Race Engines

  • Turf Warrior
  • **
  • Posts: 327
  • Karma: 4
  • Gender: Male
  • A.C.E. race engines
    • View Profile
Re: mikuni carbs
« Reply #3 on: March 12, 2012, 10:44:18 am »
Quote from: ajm57 on March 12, 2012, 08:00:24 am
38 cube long rods .02 over cam and flywheel. 35 cube heads
I will mill the heads ~.035- .04 if I go single carb.  or more with dual carb.
I'm just trying to figure which way to go and what to use. I want to make sure I have enough, but I don't want to go to far either. Any suggestions are apprieciated.


personally, on small tracks i would run a pair of 24mm flat slides, on bigger than 1/8mi i would go with 28's.
Logged
home of A.C.E. the race engines
\"building winning race engines..one at a time\"
ronatchison@live.com  FB>Ace Racing and Performance.

Offline ajm57

  • Newbie
  • *
  • Posts: 27
  • Karma: 0
  • Gender: Male
    • View Profile
Re: mikuni carbs
« Reply #4 on: March 12, 2012, 02:29:07 pm »
Thanks
Logged
Arthur

Offline Ron Atchison/A.C.E. Race Engines

  • Turf Warrior
  • **
  • Posts: 327
  • Karma: 4
  • Gender: Male
  • A.C.E. race engines
    • View Profile
Re: mikuni carbs
« Reply #5 on: March 13, 2012, 12:39:49 am »
no prob. ...your carb selection is as important as your cam, especially with duals!
Logged
home of A.C.E. the race engines
\"building winning race engines..one at a time\"
ronatchison@live.com  FB>Ace Racing and Performance.
Pages: [1]   Go Up
« previous next »